-
$41.17
$52.12Dentfix DF-609 Utility Wedge Set, Nylon, Dismounting Lever, Wedge 30mm, and Wedge 60mm
DentFix DF-609 Utility Wedge Set, Dismounting lever, wedge 30 mm, and wedge 60 mm – Made in Germany. Constructed from high quality nylon. This tool set is so versatile you will wonder how you managed without it.
-
$97.82
$130.34Dentfix DF-8 1/4″ Hole Punch Pliers
DentFix DF-8 1/4″ Hole Punch Pliers – This is the most efficient hole punch that you will ever own. You”ll be amazed at how little pressure is needed to punch out holes. With the one and one quarter inch deep throat you will be able to get the best overlap capability for your plug welds.
-
$75.71
$100.94Dentfix DF-900PM 500 Qty Alu Magnesium Studs M4X25
DentFix DF-900PM 500 Qty Alu Magnesium Studs M4x25 – consumable magnesium stud pins for the DF-900A and DF-900DX. For use with Series 5 & 6 Aluminum Panels.
-
$84.22
$112.29Dentfix DF-900PS 500 Qty Alu Silicon Studs M4X25
The DF-900PS is the consumable silicon stud pins for the DF-900A and DF-900DX. These optional studs are intended for a better stick to aluminum alloy panels used on some Audi’s, Ferrari’s and Lamborghini’s. Bag of 500
-
$43.07
$55.58Dentfix DF-DB79K Dead Blow Hammer Kit with 6 Tips
Dentfix DF-DB79K Dead Blow Hammer Kit with 6 Tips – a unique Dead Blow Hammer that can adapts to the technicians paint less dent repair (PDR) tool needs with interchangeable tips. The dual head gives the user two striking ends to knock down high spots on dent repairs. Depending on the situation the steel metal tip can be used for bare steel panels.
Kit includes 6 different interchangeable screw on tips:
• Aluminum Round
• Steel Round
• Rubber Round
• Plastic Flat
• Brass Round
• Brass FlatWhen working with aluminum panels use the aluminum tip to prevent contamination. The rubber or plastic tips can be used for a softer touch when performing paint less dent repair on painted aluminum or steel panels (do not cross contaminate). Both brass tips are non-sparking. Also includes blow-molded storage case.
Blowback is eliminated thanks to the dual flex neck that cushions each strike. Flip the tool over and the chiseled end is perfectly suited for prying off door trim panels or removing glue residue and glue attached PDR pulling tabs. The tool is seven inches in overall length.
-
$24.15
$30.57Dentfix DF-DSP310 Door Skin Pliers
Dentfix DF-DSP310 Door Skin Pliers – Single
LARGE RUBBER PAD – Prevents the risk of damaging the front door skin.
T-BAR – Spreads the clamping force and the cushioned outer pad prevents paint marring.
ADJUSTABLE & LOCKABLE – Customize the clamp to perfectly to the required opening and position needed.
CONSTRUCTION: SteelThe Door Skin Pliers are a high quality, adjustable locking clamp specifically designed to hold a door skin in place while allowing full access to the rear door frame flange. Equipped with a large rubber pad on the front to prevent the risk of damaging the front of the door skin. The “T” bar on the rear side of the clamp allows the user to clamp down the door skin and hold it while bending the skin flange around the door frame.
**It is recommended to use in pairs. -
$2,979.32
$3,385.59DentFix DF-EZN1 EZ Nitrogen Plastic Welder – Bottle
DentFix DF-EZN1 EZ Nitrogen Plastic Welder – The DF-EZN1 EZ NITRO PLASTIC WELDER is unique in its use of proprietary Flow Adjust Switch Technology (FAST). The FAST system makes the DF-EZN1 the easiest nitrogen welder to learn and use. It simplifies nitrogen welding and eliminates flow adjustments by the user. This significantly reduces the time to set up the welder and gets the work done FAST.
Equipped with two welders, the DF-EZN1 EZ NITRO incorporates both a nitrogen welding torch and an airless welding torch. The nitrogen torch is air cooled. It is essential to establish and maintain air flow before turning the welder on, and air flow must be maintained until the nitrogen torch cools down. (Usually 10 minutes to cool down after powering down)
The unit comes with plastic rod in various types and sizes to enable the user to weld different types of plastic and different types of damages. Also included is a roll of aluminum tape to hold parts together when welding. The hand seaming tool help shapes, flatten, and insure that repaired flanges and tabs are the correct thickness.
The cart is equipped with a tank regulator, tank brackets, tank chain, a heat gun holster, and a power strip for powering other tools.
-
$4,386.64
$4,984.81DentFix DF-EZN1G EZ Nitrogen Plastic Welder – Generator
The DF-EZN1G EZ Nitro Plastic Welder Generator eliminates the need for refilling nitrogen tanks and has a smaller footprint taking up less space in the shop thanks to its onboard nitrogen generator. The proprietary Flow Adjust Switch Technology (FAST) system makes the DF-EZN1G the easiest nitrogen welder to learn and use. It simplifies nitrogen welding and eliminates flow adjustments by the user. This significantly reduces the time to set up the welder and gets the work done FAST.
Equipped with two welders, the DF-EZN1G EZ Nitro Generator incorporates both a nitrogen welding torch and an airless welding torch. The nitrogen torch is air cooled. It is essential to establish and maintain air flow before turning the welder on, and air flow must be maintained until the nitrogen torch cools down. (Usually 10 minutes to cool down after powering down)
The unit comes with plastic rod in various types and sizes to enable the user to weld different types of plastic and different types of damages. Also included is a roll of aluminum tape to hold parts together when welding. The hand seaming tool help shapes, flatten, and insure that repaired flanges and tabs are the correct thickness.
The cart is equipped with a heat gun holster, and a power strip for powering other tools.
The welder uses 110volts and a maximum of 10amps, total consumption is a maximum of 600watts. -
$6,482.64
$7,366.63DentFix DF-EZN1G/DXE EZ Nitro Plastic Repair Station – Extended
The EZ Nitro Plastic Repair Station – Extended: Engineered to meet the needs of Premier Auto Body Shops everywhere. Utilizing an Award Winning Nitrogen Plastic Welder with a Dual Chamber Nitrogen Generator, the DF-EZN1G/DXE converts shop air into nitrogen and there is no need to refill nitrogen bottles! The easiest to use and most capable plastic welder station EVER, by Dent Fix!
The proprietary Flow Adjust Switch Technology (FAST) system makes the DF-EZN1G/DXE the easiest nitrogen welder to learn and use. It simplifies nitrogen welding and eliminates flow adjustments by the user. This significantly reduces the time to set up the welder and gets the work done FAST.
In addition to a nitrogen welder the kit also includes a thermoplastic hot stapler kit, complete with 7 variety of staples, three mini die grinders with 3 different bits, hand seamer, heat gun, ring hammer, multi-clip pliers, shaping tools, trim removal tools, and a variety of plastic welding rods (ABS, Polypropylene, Polycarbonate, Polyethylene, and Polyurethane).
As added bonus, a high pressure N2 Outlet gives you the ability to attach air-powered tools to the side of the unit and run on nitrogen! Nitrogen is beneficial because it has a lower moisture content, compared to shop air, which helps safeguard the internals from corrosion.
The DF-EZN1G/DXE EZ Nitro Plastic Repair Station by Dent Fix Equipment is everything you need your plastic repair station to be and more.
Kit Includes:EZ Nitro Plastic Welder with Nitrogen and Airless Plastic Welding capabilities
On-board Nitrogen Generator – Creates nitrogen from the atmosphere eliminating the need to refill bottles!
Hot Stapler – Deluxe Kit with 7 varieties of StapleClips (DF-800BR)
Assortment of Plastic Welding Rods (ABS, Polypropylene, Polycarbonate, Polyethylene, and Polyurethane)
Three (3) Mini Die grinders with 3 Unique Bits
Electronic-Controlled Heat Gun (DF-900HG)
Double End Nylon Dolley (DF-900DEND)
Round Head Nylon Chisel (DF-900RHND)
Aluminum Tape (DF-EZN1-AT150)
Multi-Clip Pliers (DF-625)
Plastic Clip Pliers (DF-624CP)
Clip Lifter (DF-618CL)
Hand Seamer (DF-EZN1HS)
Ring Hammer (DF-903)
Dust Cover
Utility Wedge Set (DF-609)
Plastic Lever Scraper (DF-WK20)
Heat Gun Holster
Lockable Cabinet with Keys
5 Year Manufacturer Warranty -
$52.70
$68.00Dentfix DF-SP360 Shunting Pliers
Dentfix DF-SP360 Shunting Pliers
Pliers allows for squeeze-type resistance spot welds in coated steels
Allows for a superior Spot Weld and Larger Nugget or Spot ( Watch Video )
Shunting the current flow, to create a successful spot weld
Pliers facilitates the electrical current from one side to the other
Saves E-Coat on the mating surfacesSqueeze-type resistance spot welding (STRSW) sometimes requires additional measures, in the form of shunting the current flow, to create a successful spot weld. Conductive coatings on steel, such as zinc or weld-through primer increase the resistance but a successful weld can be accomplished. Non-conductive coatings on steel, such as E-Coat (a corrosion-resistant primer applied to parts by the manufacturer) inhibit the completion of the spot weld. The E-Coat on the mating surfaces can be saved when using STRSW with the use of the Dent Fix Shunting Pliers (DF-SP360).
Simply remove the coating from only the outside surfaces, position the shunting clamp at the spot weld site, and the spot weld is made at the adjacent site. The current chooses the path of least resistance when confronting the non-conductive E-Coat, the shunting pliers facilitates the electrical current from one side to the other. The E-coat at the mating surface burns away.
-
$35.50
$44.94Dentfix DF-SPD66-10 Cup and Screw for the DF-15 (10 Pack)
This cup and screw attaches to the end of the C-Clamp of the DF-15 Spot Weld Drill Series to protect the C-Clamp.
-
$75.71
$100.94Dentfix DM510DBW PDR Striped White Ding Board
DentFix DM510DBY PDR Striped Yellow Ding Board
