-
$34.05
$43.10DentFix DM520GS 10pcs Ding Massager Glue Sticks
DentFix DM520GS 10pcs Ding Massager Glue Sticks
-
DIRECT FIRED AMU HEATING SYSTEM
AMU Heating System
- Vertical / Side Discharge configuration
- White Powder coat finish
- ETL Listed Control Panel
- Single point connection
- Exhaust VFD fused and wired
- Hour meter
- Control panel messages
- Time display shows cycle time and elapsed time
- Truly variable air flow
- Interlock status indicator lights
- 30′ Umbilical card
- Easy-to-use controls
-
$6.60
$8.91Dowel Pin – Chief Ez Liner II & S21 (after 708)
Dowel Pin – Chief Ez Liner II & S21 (after 708)
- S-21 & EZ Liner II Frame Machine Tower Machine dowel pin 3/8 X 1″ ( pin is for S-21 frame machine with Serial # 708 And Down)
- Dowel is 5/16″ X 1″
- Requires one pin per Bearing
- Replaces Chief Part # 606109
Replacement for Chief EzLiner II & S21Frame Machine Tower Roller Bearings (Takes 4 bearings per tower) cyr 1-1/8 Bearings Dowel Pin
This is a Non-OEM, Aftermarket, Replacement Part That Replaces Original
-
$6.60
$8.91Dowel Pin – Chief S21 Frame machine 3/8 X 1″
Dowel Pin – Chief S21 Frame machine 3/8 X 1″
- S-21 Frame Machine Tower Machine dowel pin 3/8 X 1″ ( pin is for S-21 frame machine with Serial # 708 And Down)
- Dowel is 3/8 X 1″
- Requires one pin per Bearing
- Replaces Chief Part # 602001
Replacement for Chief EzLiner II Frame Machine Tower Roller Bearings (Takes 4 bearings per tower) 1-1/4 Bearings Dowel Pin
This is a Non-OEM, Aftermarket, Replacement Part That Replaces Original
-
$14,898.65
$18,898.65ELECTRIC AMU HEATING SYSTEM
AMU Heating System
- Vertical / Side Discharge configuration
- White Powder coat finish
- ETL Listed Control Panel
- Single point connection
- Exhaust VFD fused and wired
- Hour meter
- Control panel messages
- Time display shows cycle time and elapsed time
- Truly variable air flow
- Interlock status indicator lights
- 30′ Umbilical card
- Easy-to-use controls
-
$45,000.00
$65,000.00EURO-LINER FRAME MACHINE-INDUSTRY LEADING 10,000 LB LIFTING CAPACITY
Specifications:
• Minimum Height: 15 inches
• Maximum Height: 48 inches
• Overall maximum height with towers attached: 108 inches (9 ft.)
• Tower Height: 60 inches plus (height extensions included)
• Tower Length: 52 inches (4.3 ft.)
• Tower Height with Extension: 90 inches
• Rack Length: (w/o tower & ramps): 18 ft.
• Rack Length (w/tower & ramps): 24.4 ft.
• Rack Width (w/o ramps): 46 inches
• Rack Width (w/ramps): 82 inches
• Ramp Width: 17.75 inches
• Weight of Rack: 3000lbs.
• Maximum Lift Capacity: 10,500 lbs.
• Power required: 110v single phase 25-30 amp dedicated service
• Minimum Compressed Air: 110 psi
• Maximum Compressed Air: 145 psi
• Hydraulics for Lift: TITANIUM Electric Hydraulic System
• Hydraulics for Towers: SPX Power Team 10 ton foot pump
• Hydraulics for Towers: TITANIUM 10 ton 10 inch stroke ram
• Tower Pulling Force: 10 Ton
• 360 Degree Pulling Capacity: Yes
• Above Ground or In Ground Installation: Yes
• Designed for In Ground Pit InstallationPackage includes:
• TITANIUM Euro-Liner 18 ft. Bench Rack
• TITANIUM electric hydraulic system, control cabinet including hand pendant (for raise & lower)
• (2) SPX Power Team 10 Ton foot pumps (for towers)
• (2) Ten ton towers loaded with TITANIUM 10 ton 10 inch rams
• (2) Grade 100 high alloy pull chains w/forged slip hooks
• (10) Floor anchor bolts
• (5) Down pull assemblies
• (2) Removable zinc coated drive on ramps
• (4) Heavy duty forged pinch weld clamp assemblies
• (4) Truck anchor clamps
• (2) Pillar jacks w/mounting adapters -
$2,739.00EZ Roller Spinner Heavy Duty Mobility Package – (4) 22″ & 25″ wheels
Each Wheel Features
- Heavy duty wheels equipped with pre-installed roller bearing (see photos)
- Each heavy-duty wheel has a 3,300 lbs. rating
- 2 in 1 Roller wheel transforms into a spinner and stationary Wheel by removing the bolts holding the center.
- 10 Wedge Nuts – serviceable and easy to install
- Super strong spinner ring allows for spinner functionality
- Easy “install and go” feature
- Installation uses OEM bolts and nuts, no need to stock special parts
- Easy to move vehicles without wheels from outside lot into shop
- Lightweight thermoplastic material, makes it easy to pick up and install
- The heavy duty 10 mm steel center hub was designed to handle high impact wrenches, thus preventing over-torqueing
- Wheels have built in spacer, clears all brake calipers.
- 22″ wheels are not recommended for use with vehicles under 6″ Clearance
- 25″ Wheels are recommended for use on vehicles under 6″ Under body clearance
- Works in conjunction with the vehicle’s braking system
- EZ Roller wheel works independent of the braking system when using in the Spinner mode
- All wheels are limited to 5 mph and in shop or storage lot and 2 mph when pushing the vehicle while in Spinner mode.
- Ok to use electric pushers at low speed
- Wheel are not for road use
- 2-year warranty on Roller, 1-year warranty on Spinner ring.
-
$0.00EZ Wheel Chocks – EZ Roller Spinner 2 Pack
This is a 2 Pack of EZ Wheel Chocks, The work with all version and Sizes of the EZ Roller Spinner, Fast and easy to install
- 2 Pack
- Works with both 4/5 Lug and th 5/6 lug version
- Fast and easy to install
- Tap in to install
-
$68.63
$78.92Fastener Bar Bolt Kit – EZ-Liner II
Fastener Bar Bolt Kit
- Works with Chief EZ-II, Classic & EZ-25 frame machines
- Grade 8 harden bolt & washers
- Pkg of 4 (3/4-10NC x 4 1/2)
- Replaces Chief bolt Part # 685265
-
$64.63
$74.32Fastener Bar Bolt Kit for Excelerator Metric
Fastener Bar Bolt Kit Excelerator
- Works with Chief Excelerator
- Metric Bolts
- Grade 8 harden Bolts & Washers
- Pkg of 4 Bolt,M20X2.5X110MM Hex w/Washers
- Replaces Chief Bolts p/n 539007
-
$68.63
$78.92Fastener Bar Bolt Kit for S-21 Chief
Chief Fastener Bar Bolt Kit S-21
- Works with Chief S-21 & Signatures Frame machines
- Grade 8 harden Bolts & Washers
- Pkg of 4 (3/4″-10NC x 5 1/2)
- Replaces Chief Bolts p/n 620496
