-
$4,395.60
$4,995.00Dentfix DF-GM/DXE GLUEMAX Glue Repair Station
Elevate your Glue Panel Repairs to the MAXIMUM !
The GLUEMAX Glue Repair Station DF-GM/DXE is the ultimate pulling station equipped with both cold and hot glue pulling options. From heavy duty glue GPR pulls to cosmetic PDR corrections this kit has your shop’s needs covered.
APPLICATION
Multiple cold and hot glue pulling options to repair damage in automotive steel and aluminum panels while preserving OEM coatings and interior integrity.FEATURE & BENEFITS
HOT & COLD GLUE – Repair panel damage utilizing the advantages of both methods.
HEAVY DUTY PULLS – Our Xtreme Glue Pulling system allows for powered assisted pulls.
SMALL & DETAIL CORRECTIONS – Ultra Ding Massager Kit for controlled pulls for small areas.
STORAGE & PROTECTION – Enclosed and lock-able cart protects the tools from the shop environment.
INCLUDED IN THE KIT
DF-CGS71 Cold Adhesive Glue Slide Hammer Kit
DF-CGS72 Cold Adhesive Glue Pads Kit w/Cold Glue “Mammoth Tar”
DF-CGLB Arctic Ice Light Blue Cold Glue
DF-GPX Xteame Glue Puller
DF-DM555UDX Ding Massager Deluxe
DF-DM55DE Ding Enhancer Shield
DF-DM510DBY Yellow Ding Board
DF-505BP Bridge Puller
DF-509 9-Finger Bear Claw
DF-504 4-Finger Bear Claw
DF-900TP T-Puller
DF-900LP Leverage Puller
DF-DB79TK Knockdown Tool
DF-935LED LED Ligh -
$34.05
$43.10DentFix DM520GS 10pcs Ding Massager Glue Sticks
DentFix DM520GS 10pcs Ding Massager Glue Sticks
-
DIRECT FIRED AMU HEATING SYSTEM
AMU Heating System
- Vertical / Side Discharge configuration
- White Powder coat finish
- ETL Listed Control Panel
- Single point connection
- Exhaust VFD fused and wired
- Hour meter
- Control panel messages
- Time display shows cycle time and elapsed time
- Truly variable air flow
- Interlock status indicator lights
- 30′ Umbilical card
- Easy-to-use controls
-
$6.60
$8.91Dowel Pin – Chief Ez Liner II & S21 (after 708)
Dowel Pin – Chief Ez Liner II & S21 (after 708)
- S-21 & EZ Liner II Frame Machine Tower Machine dowel pin 3/8 X 1″ ( pin is for S-21 frame machine with Serial # 708 And Down)
- Dowel is 5/16″ X 1″
- Requires one pin per Bearing
- Replaces Chief Part # 606109
Replacement for Chief EzLiner II & S21Frame Machine Tower Roller Bearings (Takes 4 bearings per tower) cyr 1-1/8 Bearings Dowel Pin
This is a Non-OEM, Aftermarket, Replacement Part That Replaces Original
-
$6.60
$8.91Dowel Pin – Chief S21 Frame machine 3/8 X 1″
Dowel Pin – Chief S21 Frame machine 3/8 X 1″
- S-21 Frame Machine Tower Machine dowel pin 3/8 X 1″ ( pin is for S-21 frame machine with Serial # 708 And Down)
- Dowel is 3/8 X 1″
- Requires one pin per Bearing
- Replaces Chief Part # 602001
Replacement for Chief EzLiner II Frame Machine Tower Roller Bearings (Takes 4 bearings per tower) 1-1/4 Bearings Dowel Pin
This is a Non-OEM, Aftermarket, Replacement Part That Replaces Original
-
$14,898.65
$18,898.65ELECTRIC AMU HEATING SYSTEM
AMU Heating System
- Vertical / Side Discharge configuration
- White Powder coat finish
- ETL Listed Control Panel
- Single point connection
- Exhaust VFD fused and wired
- Hour meter
- Control panel messages
- Time display shows cycle time and elapsed time
- Truly variable air flow
- Interlock status indicator lights
- 30′ Umbilical card
- Easy-to-use controls
-
$45,000.00
$65,000.00EURO-LINER FRAME MACHINE-INDUSTRY LEADING 10,000 LB LIFTING CAPACITY
Specifications:
• Minimum Height: 15 inches
• Maximum Height: 48 inches
• Overall maximum height with towers attached: 108 inches (9 ft.)
• Tower Height: 60 inches plus (height extensions included)
• Tower Length: 52 inches (4.3 ft.)
• Tower Height with Extension: 90 inches
• Rack Length: (w/o tower & ramps): 18 ft.
• Rack Length (w/tower & ramps): 24.4 ft.
• Rack Width (w/o ramps): 46 inches
• Rack Width (w/ramps): 82 inches
• Ramp Width: 17.75 inches
• Weight of Rack: 3000lbs.
• Maximum Lift Capacity: 10,500 lbs.
• Power required: 110v single phase 25-30 amp dedicated service
• Minimum Compressed Air: 110 psi
• Maximum Compressed Air: 145 psi
• Hydraulics for Lift: TITANIUM Electric Hydraulic System
• Hydraulics for Towers: SPX Power Team 10 ton foot pump
• Hydraulics for Towers: TITANIUM 10 ton 10 inch stroke ram
• Tower Pulling Force: 10 Ton
• 360 Degree Pulling Capacity: Yes
• Above Ground or In Ground Installation: Yes
• Designed for In Ground Pit InstallationPackage includes:
• TITANIUM Euro-Liner 18 ft. Bench Rack
• TITANIUM electric hydraulic system, control cabinet including hand pendant (for raise & lower)
• (2) SPX Power Team 10 Ton foot pumps (for towers)
• (2) Ten ton towers loaded with TITANIUM 10 ton 10 inch rams
• (2) Grade 100 high alloy pull chains w/forged slip hooks
• (10) Floor anchor bolts
• (5) Down pull assemblies
• (2) Removable zinc coated drive on ramps
• (4) Heavy duty forged pinch weld clamp assemblies
• (4) Truck anchor clamps
• (2) Pillar jacks w/mounting adapters -
$2,739.00EZ Roller Spinner Heavy Duty Mobility Package – (4) 22″ & 25″ wheels
Each Wheel Features
- Heavy duty wheels equipped with pre-installed roller bearing (see photos)
- Each heavy-duty wheel has a 3,300 lbs. rating
- 2 in 1 Roller wheel transforms into a spinner and stationary Wheel by removing the bolts holding the center.
- 10 Wedge Nuts – serviceable and easy to install
- Super strong spinner ring allows for spinner functionality
- Easy “install and go” feature
- Installation uses OEM bolts and nuts, no need to stock special parts
- Easy to move vehicles without wheels from outside lot into shop
- Lightweight thermoplastic material, makes it easy to pick up and install
- The heavy duty 10 mm steel center hub was designed to handle high impact wrenches, thus preventing over-torqueing
- Wheels have built in spacer, clears all brake calipers.
- 22″ wheels are not recommended for use with vehicles under 6″ Clearance
- 25″ Wheels are recommended for use on vehicles under 6″ Under body clearance
- Works in conjunction with the vehicle’s braking system
- EZ Roller wheel works independent of the braking system when using in the Spinner mode
- All wheels are limited to 5 mph and in shop or storage lot and 2 mph when pushing the vehicle while in Spinner mode.
- Ok to use electric pushers at low speed
- Wheel are not for road use
- 2-year warranty on Roller, 1-year warranty on Spinner ring.
-
$0.00EZ Wheel Chocks – EZ Roller Spinner 2 Pack
This is a 2 Pack of EZ Wheel Chocks, The work with all version and Sizes of the EZ Roller Spinner, Fast and easy to install
- 2 Pack
- Works with both 4/5 Lug and th 5/6 lug version
- Fast and easy to install
- Tap in to install
-
$68.63
$78.92Fastener Bar Bolt Kit – EZ-Liner II
Fastener Bar Bolt Kit
- Works with Chief EZ-II, Classic & EZ-25 frame machines
- Grade 8 harden bolt & washers
- Pkg of 4 (3/4-10NC x 4 1/2)
- Replaces Chief bolt Part # 685265
-
$64.63
$74.32Fastener Bar Bolt Kit for Excelerator Metric
Fastener Bar Bolt Kit Excelerator
- Works with Chief Excelerator
- Metric Bolts
- Grade 8 harden Bolts & Washers
- Pkg of 4 Bolt,M20X2.5X110MM Hex w/Washers
- Replaces Chief Bolts p/n 539007
