-
$17.53
$22.19Dentfix DF-CT887RS 5.0mm 7/32″ Plastic Pop Rivet 50 Pcs.
DentFix DF-CT887RS 5.0mm 7/32″ Plastic Pop Rivet 50 Pieces
-
$56.61
$66.92Dentfix DF-507 One Pound Thin Wiggle Wire .062 Gauge
DentFix DF-507 One Pound Thin Wiggle Wire .062 – approximately 60 pieces
-
$246.81
$290.36DentFix FBS16 Finger Belt Sander
DentFix FBS16 File Belt Sander- 16,000 RPM, 90 PSI Finger Belt Sander
Dimensions 3.25 x 2.5 x 12 in -
$33.65
$42.60Dentfix DF-503SW Slide Weight for DF-505
DentFix DF-503SW Slide weight to be used with the long rods (DF-503L) from the Maxi 505 Multiple Pull Dent Station 220V and 100V.
-
$190.85
$254.47Dent Fix DF-595IICB Circuit Board
Dent Fix DF-595IICB
Circuit Board
Relay Not Included
Relay Bolts to Board Part# df-595IIR
For model# 595II -
$87.02
$112.29Dentfix DF-I9315CW Cutting Wheel 100 X 1 X 10MM 25 Pc. Set
The DentFix DF-i9315CW Cutting Wheel is a replacement consumable for the DF-i9314 Reversible Air Cut-Off Wheel and DF-i9315CR Long Corner Grinder.
Box of 25 wheels.
-
$27.78
$35.16Dentfix DF-1610 10.0mm Spot Weld Drill Bit High Speed Steel Cobalt – Germany
DentFix DF-1610 10.0 mm Spot Weld Drill Bit High Speed Steel Cobalt – Germany – The largest diameter High Speed Steel Cobalt (HSCO) spot-weld bit we offer. The twist is larger than the shank which is 8.0mm and has a flat spot on it to be tightened into our DF-15 Series Spot Weld Drills. This German made bit may be used with off brand spot weld drills. We also offer this bit with a Titanium heat resistant coating as part # DF-1610T. Our drill bits a specifically designed for the abuse of spot weld drilling. Flat ground for strength, centering nib to prevent walking. Our German made spot weld bits are available in 3 sizes, 6.5, 8.0 and 10.0 mm. These Cobalt high-speed steel mix bits are 45mm long and work with all brands of spot-weld drills. Titanium (gold color) is a heat resistant coating that extends drill life by about 50%.
-
$32.26
$40.83DentFix 613RH 1/4″ Finger Ratchet
DentFix 613RH 1/4″ Finger Ratchet- This is the optional ratchet head for use with the Multi-handle system. This accessory pushes the DF- 615 and DF-613 kits into a whole new realm. Be sure to get one when ordering your kits.
-
$33.16
$41.97Dentfix DF-1610T Titanium Coated Hsco 10.0mm Spot Weld Drill Bit – Germany
DentFix DF-1610T Titanium Coated HSCO 10.0 mm Spot Weld Drill Bit – Germany
-
$24.15
$30.57Dentfix DF-DSP310 Door Skin Pliers
Dentfix DF-DSP310 Door Skin Pliers – Single
LARGE RUBBER PAD – Prevents the risk of damaging the front door skin.
T-BAR – Spreads the clamping force and the cushioned outer pad prevents paint marring.
ADJUSTABLE & LOCKABLE – Customize the clamp to perfectly to the required opening and position needed.
CONSTRUCTION: SteelThe Door Skin Pliers are a high quality, adjustable locking clamp specifically designed to hold a door skin in place while allowing full access to the rear door frame flange. Equipped with a large rubber pad on the front to prevent the risk of damaging the front of the door skin. The “T” bar on the rear side of the clamp allows the user to clamp down the door skin and hold it while bending the skin flange around the door frame.
**It is recommended to use in pairs. -
$54.33
$70.10Dentfix DF-503KF Weld Keys – Flat, 100/Pkg
Dentfix DF-503KF Weld Keys – Flat
Quality weld keys for steel bridge pulling.
Flat shaft intended for panel repair pulls. 100 pcWith the DF-503KEM Magnetic Key Electrode and DF-505 Maxi (both sold separately), the keys can be welded to steel panels. The DF-505BP Bridge Puller (sold separately) can then be used to perform a controlled pull and repair.
-
$80.81
$107.75Dentfix DF-1690 Tungsten Carbide Drill Bit for Boron, 3 Edge Special Coating
DentFix DF-1690
8.0 mm Drill Bit
Tungsten Carbide Drill Bit for Boron
Drill through Boron Steel is with this bit.
Cuts spot welds from Boron Steel.
Special multi-layered coated,
Drill through and survive Ultra High Strength Steel, aka “Boron Steel”.
Used with our original red ringed 1800-rpm drill or blue ringed 1000-rpm drill.
Not recommend this bit be used with off brand copies of our drill.
Proper precautions must be taken to ensure the long life of this bit.
